-
Cap head bolts
I fixed the oil leak today. While I was at it, I swapped out the pathetic little cap head bolts from the oil line brackets for M5 items. At least now I can A, see the damn things, B, find a tool to fit them. This is invaluable when accessing the depths of the bikes underside to put the brackets back on. #onlytaken3yearstosortitout
-
Are you sitting comfortably?
…This could take a while. The last couple of days have been something of a nightmare. We finally have a rebuilt motor and Saturday saw me putting it back in the frame for final fitting. Except that when I tried to fit the radiator bracket which is mounted on an engine mounting bolt, I hadn’t realised that the bolt was too short (it had torqued up ok on the previous motor) and stripped the threads in the cylinder head. Having been at it all day, I decided to leave it until Sunday so I could look at it with a fresh mind. The only option was a helicoil which I…
-
Shiny shiny
Aaaaaand I refitted the newly powder coated clutch casing today as well. In light silver which shows up nice in the sunlight, this service was applied by James at Superfinishingsuk (who will soon be opening a new premises near Dorchester in Dorset, all the best with that my man). I then complimented that by polishing the outer ring… to make it nice and shiny. I do have to redesign the gasket though as it shouldn’t be visible. Still, one step closer to getting it all back together.
-
Help, I’m bleeding…
After stripping the engine out last August, I later saw the fluid level in the clutch master cylinder had dropped. On inspection, the clutch slave cylinder seal had gone for the second time so decided to replace the whole unit. This Oberon piece landed on my doorstep recently and as the (rebuilt) engine is back in the frame, I was excited to fit it. It took 2 minutes to fit and bleed. The easiest bleeder I’ve ever done. Anyways, it all seems to work and it wasn’t expensive compared to an original Honda unit so here’s hoping it gives a better feel at the lever when it’s time to get…
-
Shimming when you’re winning
So, a large part of today was spent fitting both heads and shimming the valve gaps. As I had lapped all the valves previously, it meant that most of the shims had to be replaced. Luckily, with shims from spare heads available, we were able to complete the task. Now to get it back in the frame…
-
Gearbox – check!
The new superfinished and modified gearbox is in, the selector mechanism fitted and tis all working. Now refitting everything on the clutch side. The clutch basket has been rebuilt and polished by James at Superfinishingsuk in Bridport and is looking rather sweet. Next, the heads will be rebuilt and hopefully by the end of next week, the engine will be back together and replaced into the chassis (pronounced ‘shassee’ just in case you dint know ). We hope to try out a previously untried (by us or anyone we know of) tuning method which atm is top secret but should let us free the beast in our Mission 9 quest.
-
Prepping for rebuild
A fair bit of time yesterday was spent prepping the Ducks original engine ready for rebuild(draining of fluids, cleaning and removing old gasket material). Today, I went to advance to removing everything that didn’t need to be on there (heads and such like) only to find cylinder no 4 has a severe wear groove in the cylinder wall. I now have two choices. Get a new liner fitted which means crank and pistons out which is something we wanted to avoid or start the procedure all over again with another engine. The next engine is on the bench waiting for me to finish my (very much needed) cup of tea.…
-
Clutch slave cylinder
After 30-ish years, the clutch slave cylinder can get a little ‘loose’ and despite servicing can lose their feel and effectiveness. To this end, after finding the cylinder on the Duck weeping more than Donald Trump after the last election, I decided to upgrade. This tasty bit of kit is fairly priced and came next day delivery. Also being made in England (not too far from Duck Central as it happens) spare seals and pistons are readily available should the need arise … in about 30 years time Anyway, when the newly rebuilt engine goes back in this will be fitted and along with the other clutch mods, should give…
-
Isotropic superfinishing
Hopefully this should help it breathe a little better. Had the clutch baskets and cams isotropically superfinished by @Superfinishingsuk James also did the head work to my specification. The clutch steels have been semi polished to remove the sharp edge from when they were stamped out. Hopefully this spec will allow the plates to move freely without loss of friction coefficient. This part is an experiment to try to give the clutch a little more feel. If you think you would like some polishing done or heads flowed, James is a racer with on track experience so knows how these changes make a difference for the better. The clutch cover…
